Actually, if you believe the math, an x-ray laser (like those generated by x-ray laser warheads) is a ravening death beam:
Bottom line is an x-ray laser is technologically very challenging, but if you manage to make one you have an Unstoppable Death Ray of Stupendous Range.
Luke Campbell:
Let's take a 10 MW ERC pumped FEL at just above the lead K-edge. This particular wavelength is used because lead is pretty much the heaviest non-radioactive element you can get, and at just above the highest core level absorption for a material you can get total external reflection at grazing angles - so no absorption or heating of a lead grazing incidence mirror. We will use a 1 meter diameter mirror. The Pb K-edge x-ray transition radiates at 1.4E-11 m. This gives us a divergence angle of 1.4E-11 radians. At 1 light second, we get a spot size of 5 mm, and an intensity of 5E11 W/m2.
Looking at the NIST table of x-ray attenuation coefficients, and noting that 1.4E-11 m is a 88 keV photon, we find an attenuation coefficient of about 0.5 cm2/g for iron (we'll use this for steel), 0.15 cm2/g for graphite (we'll use this for high tech carbon materials) and 0.18 cm2/g for borosilicate glass (a very rough approximation for ceramics). Since graphite has a density of 1.7 g/cm3, we get a 1/e falloff distance (attenuation length) of 4 cm. Iron, with a density of 7.9 g/cm3, has an attenuation length of 0.25 cm. Glass, density 2.2 g/cm3, has an attenuation length of 2.5 cm.
At 1 light second, therefore, the beam is depositing 2E12 W/cm3 in iron at the surface and 7E11 W/cm3 at 0.25 cm depth; 1.2E11 W/cm3 in graphite at the surface and 5E10 W/cm3 at 4 cm depth; and 2E11 W/cm3 in glass at the surface and 7E10 W/cm3 at 2.5 cm depth. Using 6E4 J/cm3 to vaporize iron initially at 300 K, we find that iron flashes to vapor within a microsecond to a depth of 0.9 cm. The glass, assumed to take 4.5E4 J/cm3 to vaporize (roughly appropriate for quartz) will flash to vapor within a microsecond to a depth of 4 cm within a microsecond. Graphite, at 1E5 J/cm3 for vaporization, will flash to vapor to a depth of 0.7 cm within a microsecond (the laser performs better if we let it dwell on graphite for a bit longer, we get a vaporization depth of 10 cm after ten microseconds).
Net conclusion - ravening death beam at one light second.
Now lets look at one light minute. The beam is now 30 cm across. This is much deeper than the attenuation length in all cases, so we will just find the radiant intensity and the equilibrium black body temperature of that intensity. We have an area of 7E-2 m2, and an intensity of 1.4E8 W/m2. You need to reach 7000 K before the irradiated surface is radiating as much energy away as heat as it is receiving as coherent x-rays. The boiling point of iron is 3023 K, the boiling point of quartz is 2503 K, and the sublimation temperature of graphite is 3640 K. All of these will be vaporized long before they stop gaining heat. At this range, the iron is subject to 5.6E8 W/cm3 at the surface, the graphite to 3.3E7 W/cm3 at the surface, and the glass to 5.6E7 W/cm3 at the surface. Using the above values for energy of vaporization, we get about 0.1 milliseconds before the iron starts to vaporize, 0.8 milliseconds before the glass starts to vaporize, and 3 milliseconds before the graphite begins to vaporize (because of its long attenuation length, once it begins to sublimate, graphite sublimates rapidly to a deep depth, while you essentially have to remove the iron layer by layer).
Net conclusion - still a ravening death beam at one light minute.
What about at one light hour? The beam is 18 meters across. The equilibrium black body temperature is 900 K. This is well below the melting point of most structural materials. Ten megawatts, however, is a lot of ionizing radiation. Any unhardened vehicle will be radiation killed at these ranges.
However, he goes on to note that in order to boost electrons to the velocities required for an X-ray free electron laser, you will need an acceleration ring approximately one freaking kilometer in diameter. So this X-ray laser would only be suitable for exceedingly huge warships, orbital fortresses, and Death Stars.
Since the time he wrote the above, Luke Campbell has reconsidered the use of lead grazing incidence mirror. Now he favors using diffraction.
Luke Campbell:
I have since come to realize that at x-ray energies this high, matter cannot act as a mirror even at grazing angles (the x-rays have such a short wavelength that they interact with the atoms individually, rather than seeing them as a flat sheet - and you can't really get grazing incidence off of an individual atom). This is why I now prefer diffraction for focusing.
